Surface: Wrinkle
Chemistry : Polyester
Use : Indoor or outdoor use
Applied by electrostatic spraying gun that can provide negative tension of 60-80 kV.
Curing schedule : 180-200ºC /10-15 minutes depending on the powder chemistry.
Optimal film thickness : 80 -110 um.
The size of wrinkle pattern obtained depends on the coating thickness.
Excessively thin or thick films will not give a satisfactory finish.
7-10m³/kg, the membrane is 60μm(calculate by 100% utilization rate of powder coating).
Store below 30 °C, ventilated, dry, clean room, not near the fire, heat, direct sunlight, open dumps is prohibited.Under this condition, the powder can be stable for 12 months, more than the storage period may be re-examined, such as the results meet the requirements, can still be used.
This product is non-toxic. In the course of inhalation of dust should be avoided. The operators should wear appropriate dust mask and glasses.
| Chemistry Property | Inspection Standards | Test Indicators (High light) | Test Indicators (Glazed/Matte/Low light) |
|---|---|---|---|
| Impact resistance | ISO 6272. GB/T 1732-1993 | 50kg/cm | 40kg/cm |
| Cupping test | ISO 1520. GB/T 9753-1988 | 8mm | 7mm |
| The adhesion (grid method) | ISO 2409. GB/T 9286-1998 | 0 | 0 |
| Bending | ISO 1519. GB/T 6742-1986 | 2mm | 3mm |
| Pencil Hardness | ASTM D3363. GB/T 6739-1996 | 1H-2H | 1H-2H |
| Salt spray test | ISO 7253. GB/T 1771-1991 | >500 hours | >500 hours |
| Damp heat test | ISO 6270. GB/T 1740-1979 | >1000 hours | >1000 hours |
| Heat resistance | 110℃/24 hours (white) | Good gloss retention, ΔE≤0.3-0.4 | Good gloss retention, ΔE≤0.3-0.4 |
| Florida weathering exposure | ISO 2810. South 45°, 12 months | Gloss retention≥50% | Gloss retention≥50% |
| Artificial accelerated aging | 60℃/8 hours + 50℃/4 hours condensing, cycle for 500 hours | Gloss retention≥50%, Color stability: ΔE≤0.35 | Gloss retention≥50%, Color stability: ΔE≤0.35 |
| Annotate | 1. The above experiment uses 0.8mm steel with degreasing and rust removal, and the coating thickness is 50–70 microns.2. The above coating performance may be lower for glossy and slightly lower gloss finishes. | — |
Powder coatings can be categorized by resin system (epoxy, polyester, hybrid, polyurethane), appearance (smooth, texture, hammer, metallic, pearlescent), or performance level (anti-corrosion, heat-resistant, UV-resistant, architectural grade, automotive grade).
Powder coatings offer thousands of colors in gloss, matte, satin, metallic, candy, texture, wrinkle, hammer tone, wood grain, fluorescent, and other custom effects. Special powders can create soft-touch, anti-scratch, anti-fingerprint, or anti-graffiti surfaces.
The process generally includes surface pretreatment (degreasing, phosphating, chromating, sandblasting), drying, electrostatic spraying, curing in an oven, and cooling. A well-controlled pretreatment and curing process ensures strong adhesion and long service life.
Powder coatings are environmentally friendly, solvent-free, and produce minimal waste. They offer excellent corrosion resistance, weather durability, mechanical strength, and uniform film appearance. The coating is tough, impact-resistant, scratch-resistant, and has a long lifespan.
Powder coatings are widely used in appliances, aluminum profiles, architectural components, automotive parts, bicycles, furniture, outdoor equipment, machinery, electrical cabinets, pipeline systems, and general industrial and consumer goods.
Powder coating is a dry finishing technology where finely ground powder is electrostatically sprayed onto a metal or non-metal surface and then cured at high temperature. After curing, the powder melts into a continuous, durable, and decorative coating layer.
Powder coating protects the substrate from corrosion, weathering, chemical attack, and mechanical wear. It also provides decorative appearance with rich colors, gloss levels, textures, and special effects.
In many industrial applications, powder coating outperforms liquid paint. It forms a thicker and tougher coating, resists corrosion and chemicals better, and does not contain VOCs. It also provides excellent consistency and cost-effective mass production.
It is called powder coating because the coating material is a solid powder instead of a liquid paint. The coating is formed by melting and curing powder particles under heat.
Powder coatings include several families depending on resin chemistry:
• Epoxy powders
• Polyester powders
• Epoxy-polyester hybrid powders
• Polyurethane powders
• Acrylic powders
• Fluorocarbon (PVDF) powders
Each type has its own performance features such as corrosion resistance, UV resistance, chemical resistance, outdoor durability, or decorative properties.
Powder coatings are based on thermoset or thermoplastic resins combined with pigments, curing agents, fillers, additives, and in some cases metallic or effect particles. Common substrates include steel, aluminum, galvanized metal, MDF, and certain heat-resistant plastics.
The lifespan depends on powder type, film thickness, application method, pretreatment, and service environment. Indoor coatings can last more than 10–20 years. High-grade outdoor polyester or fluorocarbon powders can last 15–25 years or longer under UV exposure.
For help with solutions customized to your business needs, contact Export Director now.
Export Director
With 30+ years of experience and We firmly believe that product quality is the basis of cooperation.
Send Inquiry
TEl
+86 132 6275 2056
